All hazardous locations shall be documented and this documentation shall be available ________.

Dry-type transformers 600 volts or less and not exceeding ________ can be located in hollow spaces of buildings, such as above a dropped ceiling.

Is a 480-volt, dry-type transformer considered to be accessible where the transformer is located on a platform 8 feet above the floor?

The disconnecting means for an outside air conditioner can be located ______.

The disconnecting means for an outside air conditioner can be located ______.

A 240-volt, ¾-horsepower, single-phase AC motor has a full load current of ________.

As a general rule, a disconnecting means shall always be located within sight from the motor. An example of an exception to that rule is ________.

Ground fault circuit interrupter (GFCI) protection shall be required for electrically heated floors in ________.

The nameplate of an AC unit shall be located so as to be ________ after installation.

The thermostatically controlled baseboard heater can serve as the disconnecting means only if ________.

When the voltage to ground does not exceed 150 volts, sufficient working space around electrical equipment shall include a minimum height of ______ for this workspace.

All fixed electric space heating equipment is considered a(n) ________ load.

All appliances operating at ________ or more shall now be listed.

For the branch circuit overcurrent device (circuit breaker) to be allowed to also serve as an appliance disconnecting means, the appliance cannot be any larger than ________.

For a hot water tank appliance rated over 300 watts, the required disconnecting means ________.

Does the NEC permit the installation of a built-in, cord-and-plug-connected microwave oven and cord-and-plug-connected range hood exhaust fan on the same 20-ampere branch circuit?

A range hood is allowed to be cord-and-plug connected as long as the cord is not shorter than _______.

A garbage disposal is allowed to be cord-and-plug connected as long as the cord is no longer than ________.

A fixed storage-type water heater that has a capacity of 120 gallons or less is considered a ________ load.

In addition to the required branch circuits installed in a home for general lighting and outlets, ______.

If an individual circuit is run for a non-motor operated appliance that is continuously loaded, the branch circuit rating must be sized no less than ________ of the marked ampere rating.

When the voltage to ground does not exceed 150 volts, sufficient working space around electrical equipment shall be a width of ______ minimum in front of the panel or the width of the panel if it is greater then that.

Fluorescent luminaires utilizing double-ended lamps and containing ballasts that can be serviced in place shall have a disconnecting means ________.

If a non-type IC (insulated covering) recessed lighting fixture is installed adjacent to combustible material, it shall be not less than ______ away from it.

Cord connected fluorescent fixtures are permitted when ________.

________ conductors shall be used for wiring on luminaire chains and on other movable parts.

Outdoor luminaires ________ permitted to be supported by trees.

Framing members of suspended ceiling systems used to support luminaires can be securely fastened to each other with ________.

An electric-discharge light fixture (fluorescent) is surface mounted over a junction box that does not support the fixture.

Branch-circuit wiring other than the circuit supplying the luminaire is not permitted to pass through the luminaire unless it is identified for ________.

A light fixture is installed in a clothes closet. It is required to have a minimum of ________ for clearance from the defined space.

Does the National Electrical Code (NEC) permit surface-mounted exposed incandescent luminaires with spiral-type fluorescent lamps in a clothes closet?

When the voltage to ground does not exceed 150 volts, sufficient working space around electrical equipment shall be a depth of ______ minimum in front of the panel.

Incandescent light fixtures installed in a clothes closet shall be a ________ type.

As a general rule, ________ grounded neutral conductor(s) can terminate on a terminal within a panelboard.

If an electrical panelboard frame is metal and it is used with nonmetallic conduit, ________.

When back feeding an overcurrent protection device such as a circuit breaker for a sub-panel feeder, ________.

________ shall be required to be legibly identified as to the purpose of use on the electrical panel.

Receptacles shall not be installed inside or _______ above bathtub or shower stall.

A 20-ampere, 125-volt and 250 volt, non-locking receptacle shall be a listed weather-resistant type ________.

As a general rule, receptacles mounted to and supported by a cover shall be held rigidly against the cover with ________.

A new installation of 120-volt, 20-ampere receptacle outlets ________.

New installations of snap switches ________ be effectively grounded.

When installing a wire termination with one copper and one aluminum conductor in the same lug, ______.

The voltage between adjacent switches and receptacles without barriers shall not exceed ________.

As a general rule, all switches shall be installed such that the center of the grip is not more than ________ above the floor or working platform.

How close can a switch be located next to a shower or hydro-massage bathtub? ( Switches must not be located within the footprint or directly above the shower opening, where they could be subject to spray or moisture. The intent is to keep switches at least 3ft horizontally from the shower opening unless they are listed for wet locations But I don’t see an exact measurement of 3 feet for a switch anywhere maybe change in the 2029 code ? we’ll see .)
This aligns with the same moisture‑protection logic used for luminaires and receptacles in 410.10(D) and 406.9(C).

Flexible cords shall be permitted to be used ________.

What is the time limit for use of a flexible cord (extension cord) when it is used in a commercial building?

A 1/0 AWG copper single conductor (column D) type W entertainment cable with 75° C terminations is rated at ________.

A #2 AWG copper 2 conductor type SJO cord is rated at ________.

Type SJO cord is rated for 300 volts and is allowed in ________.

Electrical Nometallic Tubing (ENT, Smurf Table) can be supported by openings in framing member studs on horizontal runs if they are not exceeding ________.

Conduits & raceways ______ be provided with expansion fittings where necessary to compensate for thermal expansion and contraction.

When a piece of electrical equipment has a damaged part, ______,

If a conduit or raceway is installed from a cold location to a warm location so that moisture may contact live parts, the conduit must be ______ at either or both ends.

What is the minimum cover requirement for a direct burial type UF cable that is installed outdoors that supplies a 24 volt landscape lighting system?

What is the minimum cover requirement for a nonmetallic conduit that is installed outdoors that supplies a 120 volt, 30 ampere circuit?

What is the minimum cover requirement for a direct burial type UF cable that is installed outdoors that supplies a 120 volt, 30 ampere circuit?

A direct burial underground service lateral shall have the location identified by a warning ribbon placed in the trench at least ______ inches above the wire.

Conductors emerging from an underground installation shall be protected by a raceway to at least ______ inches below grade of the minimum cover requirement.

Generally, when a raceway contains an ungrounded (hot) conductor of ______ or larger, a bushing is required at the end of the conduit when it enters the box enclosure.

When cables are installed through bored holes in wood framing members, the edge of the hole shall not be less than ______ inch(es) from the nearest edge of the wood unless a nail plate is used.

As a general rule, cables laid in a wood notch would require protection from nails or screws by using a metal nail plate at least ______ inch thick.

All conductors of the same circuit shall ______.

When an electrical box is used, any unused openings shall ______.

All electrical raceways, enclosures, and equipment ______ be connected to an equipment grounding conductor .

The size of the bonding jumper shall not be less than ______ when the size of the largest service entrance conductor is 500 KCMIL AWG copper (not paralleled)

If the rating of a circuit breaker ahead of a branch circuit is 100 amperes, the minimum size equipment grounding conductor would be a ______ AWG aluminum wire.

If the rating of a circuit breaker ahead of a branch circuit is 100 amperes, the minimum size equipment grounding conductor would be a ______ AWG copper wire.

As a general rule, equipment grounding conductors are not required to be larger than the circuit conductors supplying the equipment. When conductors are increased in size because of a long run and voltage drop concerns, ______.

Equipment grounding conductors larger than 4 AWG shall be identified ______.

An equipment grounding conductor shall be run with or enclosed with the circuit conductors. ______ is considered a type of equipment grounding conductor.

When a lightning protection system is installed, ______.

If a structure has an interior metal water piping system or any other metal piping system that may become energized ______.

The grounding electrode conductor in this case is to 2 ground rods that are 6 feet apart. As a general rule this wire ______.

Listed electrical equipment when installed shall ______.

Generally, if a metal underground water pipe is allowed and used to interconnect grounding electrodes, the grounding electrode conductor shall be connected to it ______.

A main bonding jumper or a green bonding screw provided with the panel shall be installed in a service panel ______.

A fiberglass manhole that is used to splice underground conductors for a home has a metal cover.

When a circuit breaker handle is operated vertically, ______ shall be the on position.

Electrical panels shall be installed at a readily accessible location and not be located ______.

The main electrical service disconnect for dwelling units ______.

Electrical panels with”Overcurrent protection” OCPD’s shall not be located ______.

When overhead service entrance conductors are exposed to the weather, they shall be raintight _____.

As a general rule, when more than one structure is on the same property, each building can be supplied by ______ feeder(s) from another building.

For a dwelling unit at grade level at least one receptacle outlet is required at the front and at the back. To count as this required outlet, it must be accessible and no more than ______ feet above grade.

When the National Electrical Code (NEC) specifies that electrical equipment shall be in sight from, the equipment shall be no more than ______ distant from the other.

A receptacle outlet is required for a kitchen island counter if it measures ______.

Generally, receptacle outlets in a dwelling unit shall be installed at each kitchen countertop so that no point along the wall line is more that ______ inches from a receptacle outlet.

Generally, receptacle outlets in a dwelling unit shall be installed at each kitchen counter space ______ inches or wider.

Generally, receptacle outlets in a dwelling unit shall be installed in each wall space ______ feet or more in width.

In addition to the required branch circuits installed in a home for general lighting and outlets, ______.

At dwellings, ground fault circuit interrupter protection (GFCI) shall be provided for ______ receptacle outlets.

If a cable assembly has a white conductor and it is used for a 3-way switch, a 240 volt baseboard heater, or a 240 volt hot water tank, that conductor ______ be permanently re-identified to indicate its use.

When identifying a neutral grounded conductor that is smaller than a 6 AWG, it can be properly identified ______.

What is the minimum working space clearance for a 277/480 volt system with exposed live parts on one side and grounded parts on the other?

A sealing fitting (seal off) is required in each conduit run passing from a Class-I, Division-2 location into an unclassified location. The sealing fitting ________.

The required workspace area around electrical equipment required by section 110.26 shall ______.

If you are capable of quickly reaching a piece of equipment for operation without resorting to something like a ladder to gain access, it is considered ______.